Or you could just use all of the space for a sodium battery and fully charge it as it won’t need long term storage in that state.

Lithium batteries dont like being stored fully charged they will degrade over time.

It varies quite a bit. People management, creating documentation, architecture, coding, problem solving etc. I make pretty broad jumps so it helps with resetting my focus to a new challenge. I’m a department head so it gives me some freedom in what I do. I still have the hyper focus days as well where I ignore everything but the task at hand but those are harder when you get into people management.

For me my mind will drift off and I won’t be able to stay focussed on completing repetitive tasks.

As a result thoughts of failure, stress, frustration, distraction etc will kick in and I will actively start avoiding it and sabotaging completing it until the last minute.

It only makes sense for me to try and avoid that scenario so I would say yes I have a fear of repetitive boring work/tasks but I don’t think its a phobia in the strict sense.

I would add being a few steps ahead of most others in the group, project etc because of all the over thinking you’ve done instead of sleeping or completing other things.

Im already in my mid 40’s. For me it helps to have a solid maximum cap of 4 things to juggle at a time. 2 is good 3 is great, 4 is OK but only 1 or more than 4 is looking for trouble.

Its a balancing act so if you are only upping the temperature to get higher flow but not the speeds to use that higher flow then there will be some issues. Each filament also has different temperature and flow characteristics so just because the new filament works with the current settings doesn’t mean the old filament was junk.

Knowing how lazy people are I’m betting a lot of the AI’s calls are implemented. Only the really out there ones will get dropped.

The volcano was made for high volume prints and has a bigger melt zone. Ideally it’s best for bigger nozzles, high layer hights and faster printing.

If you want to print small and detail a normal e3d or other hotend gives you better control. For smaller characters you can use a standard hotend with a 0.3mm nozzle and switch on arachnid or similar in your slicer. That will give you pretty good results provided your cooling is good.

For calibration its best to watch a few videos as its a lot to discuss over a post like this. But you are looking to do e-steps, flow-rate, temperature tower and retraction. Also know that this may change when you change the filament or speed you are printing at so try and keep things as consistent as possible.

To be honest the Volcano HE is the wrong thing for printing small detail like a DnD character. If you do all the calibrations it can print quite well but will never have the control thats needed for high detail prints. Your best bet is to have an extruder setup that makes it easy to change out the HE. I run both the volcano and normal E3D v6 and swop them out when needed with a EVA extruder.

We are all waiting. Currently a claim has been made and some other claims that it could work both from modeling and replicating the process.

We are waiting for other labs to do proper peer reviews and verify the results. That still won’t mean it does what we hope it does just that the results are the same as what was found in the original claim.

So still a long way away from knowing what is actually possible.

At home I started running Linux Mint years ago in a dual boot setup and rarely use the windows partition anymore.

For work I’ve threatened to do the same a few times but never actually got that far.

I think it helps with all the software going cloud based so the reasons of needing windows only apps are slowly disappearing even if that’s another can of worms.

Managing heat is a large part of circuit design. Superconductors can fundamentally change everything about it meaning far smaller much faster and more capable in every way. As an example 95%+ of modern CPU’s and GPUs are cooling related. The actual chips are tiny in comparison to the whole component.

Billionaires are going to Venus now. Titanic trips are so last seaso.

There are some plugins you can try in octoprint.

Personally I would probably install cura engine or PrusaSlicer on the pi SSH in and use the CLI to slice the stl and upload the gcode. You can probably write a script that monitors a folder and runs a script to do it all when a stl is dropped as well.

Most brands should work fine. Same with hairspray.

I’ve been using glass print surfaces and glue stick for 10+ years. I just wash off the glass with warm water every 2-3 prints otherwise just add a new layer of glue stick before printing. I’m going to try a G10 print surface next as I finally found some in my country.

I’ve used https://sequencediagram.org quite a bit as well. Its a text based sequence diagram generator and its been handy over the years.

Thanks I’ll give that a try. I also found another post on here about the Manifold engine that’s way faster. Its only in the dev releases at the moment and the under preferences/features/manifold

Somewhere we went from finding those who do wrong and punishing them to censor everything because everyone is bad.